EM6000-Dante dual channel receivers

This product is a digital 2-channel rackmount receiver, to match Sennheiser 6000 and 9000 series digital radio microphones. It has analogue, AES and Dante outputs. If required, for security, it can handle encrypted transmissions from 6000-series transmitters.

Contact the Equipment Rental and Sales team

No data was found

Next up

EM6000-Dante dual channel receivers


  • 19’’ 2-Channel receiver, 19 inch 1RU
  • Large 244 MHz switching bandwidth
  • Legendary Long Range mode (LR) with proprietary audio codec (SeDAC) from the masterpiece Digital 9000
  • True bit diversity utilizes both receiver paths, combines their information content to provide the best possible signal
  • Equidistant frequency grid for maximum channel density and simplest setup
  • 32 superior quality RF pre-selection filters for optimal suppression of interference signals at antenna input
  • Error correction and audio error masking
  • AES-256 encryption
  • Automatic frequency setup
  • Digital and transformer balanced analog outputs XLR, 6.3 mm jack, AES-3, EM 6000 Dante with Brooklyn II Card and Amphenol RJ-45
  • Integrated antenna splitter for cascading of up to 8 systems
  • one high-quality OLED display per channel
  • Link Quality Indicator (LQI)
  • Wireless Systems Manager (WSM) compatible
  • Compatible with standard Sennheiser UHF antennas
  • Compatible with Digital 9000 transmitters in Long Range mode
EM6000-Dante dual channel receivers


Dimensions  44 x 483 x 373 mm

Frequency response  30 Hz – 20 kHz (1.5 dB)

THD, total harmonic distortion  < 0.03 % (@ 1 kHz)

Weight  Approx. 5.2 kg

Power consumption  Max. 35 W

Audio output

Digital Audio outputs: AES3-2003, XLR-3: 48 kHz, 96 kHz, 24 bit

Dante™, RJ-45: 48 kHz, 96 kHz, 24 bit

Can be externally synchronized using WCLK loop-through with BNC sockets

Analog Audio Outputs: XLR-3 and 6.3 mm jack per channel (transformer balanced) -10 dBu to +18 dBu in steps of 1 dB (2 kΩ)

Storage temperature  -25°C to +70°C

Operating temperature  -10°C to +50°C

  • Switching bandwidth

244 MHz

Power supply 100 – 240 V AC, 50/60 Hz

Antenna connector

Input 2x BNC (50 Ω), 12 V DC, max. 200 mA each via antenna sockets, short circuit proof, Output 2 x BNC (50 Ω)

Dynamic range 111 dB (A) type

Frequency range  470 – 714 MHz

Headphone output level  6.3 mm jack, 2x 100 mW at 32 Ω

Image rejection  > 100 dB typ.

Sensitivity  -100 dBm typ.

Word clock

Input: BNC, 75 Ω

Output: BNC, 75 Ω

Sampling Rates: 48 kHz, 96 kHz

Operating relative humidity

Operation: Max. 85% at 40°C (non-condensing)

Storage: Max. 90% at 40°C (non-condensing)

Transmission method  Digital modulation, “LR” mode Min. frequency spacing for equidistant grid: 325 kHz


Analog Audio Out: 3 ms

Digital Audio Out: 3 ms (AES/EBU)

Audio codec

SeDAC (Sennheiser Digital Audio Codec)

Network protocol

IEEE 802.3-2002 (10/100 Mbit/s), shielded RJ-45 connection

Receiver Principle Double superheterodyne

Diversity principle  True bit diversity

Encryption  AES 256

Daisy chain outputs  2x BNC (50 Ω) 0 dB +/- 0.5 dB amplification relative to antenna inputs

Receiving channels  2

Daisy-chained receivers (RF)

Max. 8 EM 6000 units

Dante™ (only EM 6000 DANTE)  IEEE 802.3 (1000 Mbit/s), shielded RJ-45 connection

Power plug  3-pin, protection class I as per IEC/EN 60320-1

Water Protection Code  The product must not be exposed to dripping and splashing (IP2X)

EM6000-Dante dual channel receivers